- OS X YOSEMITE 10.10.2 BOOTABLE USB DOESNT SUPPORT FAT32 USB INSTALL
- OS X YOSEMITE 10.10.2 BOOTABLE USB DOESNT SUPPORT FAT32 USB UPGRADE
- OS X YOSEMITE 10.10.2 BOOTABLE USB DOESNT SUPPORT FAT32 USB MAC
Use "File > Export" to save the "ist"įinally, using this archived version of Multibeast, install "Drivers > Audio > Realtek ALCxxx > Without DSDT > ALC885/889a" (this will automatically select and install HDAEnabler, as well).Īfter all that, you should be good to go. This prevents OS X from resetting the CMOS (if the CMOS does reset because of Unibeast and you need help with BIOS settings for this board, let me know). On the "Kernel and Kext Patches" tab, make sure AppleRTC is checked. On the "Gui" tab, all I did was select my max resolution (1440x900) and changed the theme to mlcamp. On the "Boot" tab, make sure that "kext-dev-mode=1" is checked (this bypasses the "AppleKextExcludeList.kext", which allows the OS to boot unofficial kexts used by Hackintoshes). Leave all default check boxes and menus the way that they are unless specified or you know that it needs to be changed): Once imported, perform the following changes using Clover Configurator (Only change the things mentioned. Using Clover Configurator, import your "ist" located in "/EFI/EFI/CLOVER" (Optional) Navigate to "/EFI/EFI/CLOVER/themes" and delete all themes except for mlcamp. Navigate to "/EFI/EFI/CLOVER/kexts/" and create a folder named "10.10," unless it is already there (I believe this step is no longer necessary with Clover versions released after the one I used). If not, you can mount it with EFI Mounter v2 or Clover Configurator. Leave it checked):Īt this point, you should have your EFI partition mounted. Here are the boxes I selected (I believe one box was already checked that I didn't list. There is a new version of Clover out since I installed, but the installation should be similar, if not exactly the same. Still in terminal, run the command "sudo newfs_msdos -v EFI -F 32 /dev/rdisk0s1" (or replace disk0s1 with whatever your EFI partition is on). Once on the desktop, open Terminal and run "diskutil list" and find the disk labeled "EFI" and remember what disk and partition it is on (for example, mine was disk0s1).
OS X YOSEMITE 10.10.2 BOOTABLE USB DOESNT SUPPORT FAT32 USB UPGRADE
Sure thing! I wanted to upgrade from Chimera to Clover, but I couldn't figure out how so I formatted my hard drive for a clean install.Ĭreate Yosemite installation flash drive with Unibeastīoot into the new Yosemite partition using the Unibeast drive as the boot media I also installed the Realtek ALC889a and HDAEnabler kexts from an archived edition of Multibeast for Mavericks.) Edited the default ist to have a 1440x900 resolution at the bootloader and got rid of the orange hard drive icons.
OS X YOSEMITE 10.10.2 BOOTABLE USB DOESNT SUPPORT FAT32 USB MAC
Operating Systems (Installed on separate hard drives but sharing a 400GB FAT32 partition for storage and file-sharing on the Mac hard drive.):īootloader: Clover v2k r3065 (Basic Clover installation for non-UEFI motherboard. Hard Drives: Two Seagate Barracuda 7200RPM 1TB (2TB total) Wireless: Apple Airport Extreme from a Macbook with a Mini PCIe to PCIe conversion card
Memory: Patriot DDR2 800MHz 8GB (4x2GB) (4GB were added today) Graphics: ASUS NVIDIA GeForce GT 640 2GB (Used to be BFG NVIDIA GeForce 9800GT 1GB, but I upgraded this past summer.)
I built this machine back in February of 2010 (even though it is based on the 2009 build), so I figured it'd be fun to go through it and show that it's still going strong five years later!
0 kommentar(er)
